This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
mspxtaltest [2012/02/17 13:29]
john [CCS Version]
mspxtaltest [2012/02/17 13:36]
john [MSPGCC Version]
Line 61: Line 61:
     IE1 |= OFIE; // Enable Osc Fault     IE1 |= OFIE; // Enable Osc Fault
 } }
 +===== MSPGCC Version =====
 +This is the same as the above code, except it builds in MSPGCC. **NOTE:** I have not gotten this code to work! I'm just putting it here for reference, also as a reminder to fix it - though I am not familiar with mspgcc, so if someone else can figure it out, contact me.
 +<file c main.c>
 +// MSP430F20xx Demo - LFXT1 Oscillator Fault Detection
 +// Description: System runs normally in LPM3 with WDT timer clocked by
 +// 32kHz ACLK with a 1x4 second interrupt. P1.0 is normally pulsed every
 +// second inside WDT interrupt. If an LFXT1 oscillator fault occurs,
 +// NMI is requested forcing exit from LPM3. P1.0 is toggled rapidly by software
 +// as long as LFXT1 oscillator fault is present. Assumed only LFXT1 as NMI
 +// source - code does not check for other NMI sources.
 +// ACLK = LFXT1 = 32768, MCLK = SMCLK = Default DCO
 +// //*External watch crystal on XIN XOUT is required for ACLK*//
 +// M. Buccini / L. Westlund
 +// Texas Instruments Inc.
 +// September 2005
 +// Built with CCE Version: 3.2.0 and IAR Embedded Workbench Version: 3.40A
 +// modified by justin solarski to work with MSPGCC 4.0
 +#include <msp430.h>
 +#include <signal.h> // must be included for interrupt handler
 +volatile unsigned int i;
 +void main(void)
 +WDTCTL = WDT_ADLY_1000; // WDT 1s interval timer
 +IE1 |= WDTIE; // Enable WDT interrupt
 +P1DIR = 0xFF; // All P1.x outputs
 +P1OUT = 0; // All P1.x reset
 +P2DIR = 0xFF; // All P2.x outputs
 +P2OUT = 0; // All P2.x reset
 +BCSCTL3 = XCAP_3; //12.5pF cap- setting for 32768Hz crystal
 +// An immedate Osc Fault will occur next
 +IE1 |= OFIE; // Enable Osc Fault
 +_enable_interrupt(); // enable interrupts added for mspgcc
 +P1OUT ^= 0x01; // Toggle P1.0 using exclusive-OR
 +_BIS_SR(LPM3_bits + GIE); // Enter LPM3 w/interrupt
 +//#pragma vector=WDT_VECTOR removed for mspgcc
 +interrupt(WDT_VECTOR) watchdog_timer (void) //__interrupt void watchdog_timer (void) removed for mspgcc
 +_BIC_SR_IRQ(LPM3_bits); // Clear LPM3 bits from 0(SR)
 +//#pragma vector=NMI_VECTOR removed for mspgcc
 +interrupt(NMI_VECTOR) nmi_ (void) //__interrupt void nmi_ (void) removed for mspgcc
 +IFG1 &= ~OFIFG; // Clear OSCFault flag
 +for (i = 0xFFF; i > 0; i--); // Time for flag to set
 +P1OUT ^= 0x01; // Toggle P1.0 using exclusive-OR
 +while (IFG1 & OFIFG); // OSCFault flag still set?
 +IE1 |= OFIE; // Enable Osc Fault
 +And here's a makefile you can use with the above code. Remember to change the mmcu flag to reflect the MCU you're using.
 +<file c makefile>
 +CFLAGS=-Os -Wall -g -mmcu=msp430g2553
 +all: $(OBJS)
 + $(CC) $(CFLAGS) -o main.elf $(OBJS)
 +%.o: %.c
 + $(CC) $(CFLAGS) -c $<
 + rm -fr main.elf $(OBJS)
 </file> </file>
mspxtaltest.txt ยท Last modified: 2020/02/21 12:04 (external edit)
Driven by DokuWiki Recent changes RSS feed Valid CSS Valid XHTML 1.0